A running toilet is a quick road to significant water waste. An inefficient unit uses around 6 gallons per flush.

From a broken flapper to a clogged toilet to sediment buildup, the number of causes is endless. However, understanding its causes and solutions can help restore efficiency to your home.

If your toilet runs every few minutes, this is the guide for you. This article explores the causes and solutions for a running toilet. Read on to learn more.

Inspect the Flapper

Start by opening the tank and getting it out. Next, check if the rubber has wear or tears.

The flapper controls the toilet tank’s water flow. Over time, the rubber gets worn out, causing continuous water flow.

Luckily, a flapper is inexpensive and easy to replace. To do so, unhook the old material and attach the new one. You can buy a toilet at your local hardware store in Visalia, CA. 

Resize the Fill Tube

Resizing the fill tube is one of our most crucial plumbing maintenance tips.

A fill tube is what lets your tank refill and maintain the correct water level. This helps you avoid wasting water and a skyrocketing water bill.

However, the length of the fill tube can make the toilet run. You need the appropriate size to ensure it works well with the system. Water can leak from the toilet if the fill tube is too short or long.

Like the flapper, you can check the size of the fill tube by opening the tank. Ensure it connects to the overflow tube by an inch. If it extends beyond the ideal length, trim it until you reach the correct size.

If it’s too short, buy and replace the fill tube. This will help stop the siphoning effect. 

Check the Refill Valve

The next toilet components to check are the refill valve and the chain.

Like the flapper, a refill valve controls the water flow in the tank. However, it shuts off when the tank reaches the correct water level. The valve prevents it from overflowing and ensures an efficient refill.

If you have a faulty valve, the best thing to do is adjust or replace it.

First, ensure the water supply is off. Next, remove the refill valve cap and look for any blockages. A component in a clean and good condition is ideal to prevent a running toilet.

If damaged, replace the refill valve with a new one. Install it using the manufacturer’s instructions. Then, turn the water supply back on after installation and adjust it to the correct water level. 

Adjust the Float Height

Float problems can cause toilet runs every few minutes. If it sets high, water spills into the overflow tube and fails to fill. This causes the tank to refill itself constantly.

If your toilet is running every few minutes, check the float height. Fill the tank with water about an inch below the top of the overflow tube. If it goes beyond the ideal level, adjust it down.

In most cases, you can find screws that allow for height adjustments.

How do you adjust a ball float and a cup float? For a ball float, bend the arm downwards to lower the water level. If you have a cup float, slide it down the central column to adjust the height for a cup float.

Remove Blockage

Do you use soft water or hard water in your home? Visalia, CA, has an average water hardness level of 77 ppm. This shows a moderately hard water quality, containing magnesium, calcium, and carbonate minerals.

Along with debris, these minerals cause buildup in the flush valve. This prevents it from closing and damages the component, leading to a running toilet. One of our most important toilet repair tips for this is to remove blockages.

With this, clean the flush valve. Remove any visible debris around its seat. To dissolve mineral buildup, use a dash of vinegar or a commercial toilet cleaner.

Then, scrub the area with a brush. Clean the tank as well to remove sediments. Although it does not make water soft, water purification can prevent sediment buildup.

Calibrate Water Pressure 

High water pressure can disrupt the fill valve. If you have too much pressure, you can adjust it to stop your toilet from running constantly. However, it is not as easy as it seems for Californian residents.

In the cities of Hanford, Visalia, and Porterville, the water pressure often fluctuates. Different factors affect water pressure, including infrastructure issues and changes in water supply. This can make it difficult to calibrate water pressure in your home.

Experts say that the ideal pressure ranges from 30 psi to 80 psi. Use a water pressure gauge to measure the pressure in your home. Then install a regulator to adjust.

A pressure regulator manages and prevents issues with plumbing fixtures. 

Call for a Plumbing Service

If none of the plumbing solutions listed work, ask a professional for help. Call a plumbing service to address your running toilet problem. Professionals can determine the issue and provide a reliable fix.

This also enables you to prevent potential water damage. What factors should you consider when looking for a reliable plumbing service? To ensure quality and trustworthy service, it is crucial to follow these criteria.

In your local area, look at their experience, reviews, licensing, and warranty. Availability, pricing, and insurance for services can also help you make the best decision for your home.

Toilet Runs Every Few Minutes? Here’s How to Fix It

From a faulty flapper to sediment buildup, different issues can cause the running toilet in Visalia, California. It is necessary to inspect and address potential problems to resolve them right away. Regular maintenance can prevent plumbing issues from recurring.

If your toilet runs every few minutes and you do not know what to do, call a professional! Comfort Now offers excellent plumbing services that guarantee prompt repair and longevity. Further, our team provides expert guidance and solutions to fix running toilets.

Contact us at Comfort Now here!